-
CAS179 – Reverse Spinning Duct Ball with 25′ Lead.
$88.00Reverse Spinning Duct Ball with 25′ Lead. The Reverse Spinning Duct Ball with 25′ Lead is a versatile tool for both Air Duct Cleaning and Dryer Vent Cleaning. The Reverse Spinning Duct Ball creates a vortex of high velocity air that easily cleans ducts that are contaminated with dirt, dust, and lint. The Reverse Spinning Duct Ball is compatible with the Hurricane System. Spinning Duct Ball components are designed for intermittent use. Use a Hurricane Trigger Valve (CAS130) or compatible to interface this item with 1/4″ standard interchange airline fittings.
-
STC304 – 4″ Dryer Vent Cleaning Vacuum Hose Adaptor
$87.004″ Dryer Vent Cleaning Vacuum Hose Adaptor. Cleaning residential dryer vents without a collection device can be messy. Use the STC304 to connect a 2″ (1.90″ ID) vacuum hose for collecting lint as you free it from the dirty duct. The STC304 slides into a standard 4″ residential dryer duct and snugly fits because of its tapered design. The 1″ access hole allows tools to be run through the duct for thorough cleaning with compressed air tools or brushes. The vacuum hose connection on the STC304 is a perfect fit for the VAC300 HEPA Filtered Bucket Vac.
-
DPL001 – 1″ diameter duct plugs.
$85.001″ diameter duct plugs. These hard plastic duct plugs fit inside a 1″ hole, in sheet metal from #16 – #30 gauge. Plugs fit flush on flat surfaces and are not compatible with round duct work. 500 per package. *** THIS PRODUCT MAY DELIVER AS A SPECIAL ORDER, EXPECT A LEAD TIME OF 5-7 DAYS *** EXPEDITED SHIPPING WILL NOT BE HONORED FOR THIS ITEM.
-
STC008 – 8″ Tapered Starter Collar.
$83.008″ Tapered Starter Collar. The 8″ Tapered Starter Collar makes connecting your duct cleaning hose to duct work easy. The tapered collar allows for a snug hose fit, allowing plenty of space to tighten down with an adjustable clamp, CLP004. Use self piercing Zip Screws to fasten the flange of the 8″ Tapered Starter Collar to steel duct work.
-
PAT224-24 – Cammed-PSA Access Door,24″x24″
$83.00Cammed Access Door for Sheet Metal Duct Work. 24″ x 24″ Hinged Door is Secured with 4 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
-
PAT223-24 – Hinged-PSA Access Door,24″x24″
$83.00Hinged Access Door for Sheet Metal Duct Work. 24″ x 24″ Hinged Door is Secured with 2 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
-
TAP006 – 24″ Vent / Grill Mask Tape.
$82.00Vent / Grill Mask Tape. 24″ x 200′ with 12″ perforation. Use this Vent / Grill Mask Tape to block registers during duct cleanings or sealant application. Blue coloring to film makes this product easy to spot at the end of the job, and light tack allows for easy removal to reduce paint chipping.
-
FTB020 – Electrak 1 Second Stage Filter
$80.00Electrak 1 Second Stage Filter. The Electrak 1 Second Stage Pocket Filter is designed to catch the finer material that passes through the first stage filter, but is not destined for the HEPA. The Electrak 1 Second Stage Filter is ASHRAE 95% Efficient. Only the finest of particles are filtered by your HEPA pass through the Electrak 1 Second Stage Filter.
-
-
VAC309 – HEPA Filter Element for Bucket Vac.
$78.00HEPA Filter Element for Bucket Vac. Replacment filter element for the Bucket Vac is easy to install. Use the HEPA Filter for wet and dry vacuuming applications with the Bucket Vac, VAC300.
-
STC006 – 6″ Tapered Starter Collar.
$78.006″ Tapered Starter Collar. The 6″ Tapered Starter Collar makes connecting your duct cleaning hose to duct work easy. The tapered collar allows for a snug hose fit, allowing plenty of space to tighten down with an adjustable clamp, CLP004. Use self piercing Zip Screws to fasten the flange of the 6″ Tapered Starter Collar to steel duct work.
-
PAT006 – 6″ x 6″ Sheet metal duct patch, 100 pack.
$78.006″ x 6″ Sheet metal duct patch. Patches are pre-cut to size from #26 gauge metal and packaged in bundles of 100 pieces. Need to order more than one bundle, purchase 500 pieces for discounted prices. Perfect for covering 2″-4″ Hose Connections, Inspection Access, and Compressed Air and Brush Access Points, to the NADCA Standard, ACR2013. *** DUE TO CURRENT INDUSTRY WIDE MATERIAL SHORTAGES, MAXIMUM ORDER SIZE OF 100 PCS / ORDER (1 PACKAGE). PHONE ORDERS ONLY, 800-728-3828. ***
-
GEN933 – 400cc Carbon Cannister for CARB Compliancy on 6 Gallon Fuel Cell.
$78.00400cc Carbon Cannister for CARB Compliancy on 6 Gallon Fuel Cell. Add this 400cc carbon cannister to your General, Major, or Ranger vacuum and 6 gallon fuel cell for CARB comliancy.
-
GBD007 – Electrak 7 First Stage Filter
$78.0012- PACK – Electrak 7 First Stage Filter. The Electrak 7 First Stage Filter is a disposable fabric sack that catches the large debris in the air stream that will flow through your Electrak 7 HEPA Vacuum. The large debris can be removed from the sack, and the filter media should be changed on every job.
-
CAS104 – 3/8″ dia. x 50′ Compressed Air Hose.
$78.003/8″ dia. x 50′ Compressed Air Hose. This Goodyear Compressed Air Hose is rated for 300 PSI and comes with standard 1/4″ airline fittings. On the male connector side, this hose has a strain relief to extend the life of the hose at the connection site.
-
AGR653-24 – 24″ Corner Button-Lock Brush
$78.0024″ Corner Button-Lock Brush. Use this dual bristled brush with the AGR6XX series brush system to clean rectangular steel duct work. The shorter stiff bristles scrub hard on the interior positions of the rectangular duct while the longer soft bristles reach into the corners. Using this brush in both CW & CCW rotation allows for both sides of a corner to be cleaned adequetly. AGR6XX series brush cores can be refilled with new bristles as they wear, to reduce the cost of on-going operation. With the use an optional adaptor(AGR695), AGR6XX brush head can be used with nylon and fiberglass extension rods. This brush should be used with a Heavy-Duty Cable ONLY, AGR613-AGR615.
-
HCT001 – 2″ – 12″ Hole Cutter.
$76.002″ – 12″ Hole Cutter. Cut a perfect circle in up to #20 gauge sheet metal with this tool. Connect your duct cleaning vacuum hose to a round hole with a Snap Adaptor for ideal airflow.
-
ENG060 – 6 Gallon Portable Fuel Cell
$76.006 Gallon Portable Fuel Cell. Fuel fittings not included.
-
PAT224-20 – Cammed-PSA Access Door,20″x20″
$73.00Cammed Access Door for Sheet Metal Duct Work. 20″ x 20″ Hinged Door is Secured with 4 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
-
PAT223-20 – Hinged-PSA Access Door,20″x20″
$73.00Hinged Access Door for Sheet Metal Duct Work. 20″ x 20″ Hinged Door is Secured with 2 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
-
PAT222-24 – Cammed-DT Access Door, 24″x24″
$73.00Cammed Access Door for Sheet Metal Duct Work. 24″ x 24″ Hinged Door is Secured with 4 Cam-Locks. Door contains 5/8″ knock-over tabs for easy installation.
-
PAT221-24 – Hinged-DT Access Door, 24″x24″
$73.00Hinged Access Door for Sheet Metal Duct Work. 24″ x 24″ Hinged Door is Secured with Two Cam-Locks. Door contains 5/8″ knock-over tabs for easy installation.
-
RDC086 – 8″ x 6″ Steel Hose Reducer.
$72.008″ x 6″ Steel Hose Reducer. Steel Hose Reducers make connecting your hose runs fast and easy. Hose reducers are constructed of rolled steel. The construction makes for a long lasting product with a gloss black powder coat finish. Use 2″ – 12″ Adjustable Hose Clamps, CLP004, to secure hoses to reducer. This reducer connects ONE 8″ diameter hose to ONE 6″ diameter hose.
-
HDF425 – DryerFlex 4-Ply Flexible Dryer Vent Transition Hose
$69.004-Ply DryerFlex Flexible Dryer Vent Transition Hose. DryerFlex, a safe and effective airflow-efficient dryer transitin duct, combines the ease of use and flexibility of wire bound foil flex hose with semi-rigid aluminum flex. It simplifies dryer connections and protects against dangerous kinks and bends. Other ducts bend and kink, restricting the airflow and allowing lint to accumulate in the dryer exhaust system to become a fire hazard. With DryerFlex, installations are easier and laundry areas are safer. A UL Listing of UL2158A is required by building code and appliance manufacturers. DryerFlex is UL2158A Listed. Kit includes 2 stainless steel DryerClamps. This product length is 25′.
-
RDC064 – 6″ x 4″ Steel Hose Reducer.
$67.006″ x 4″ Steel Hose Reducer. Steel Hose Reducers make connecting your hose runs fast and easy. Hose reducers are constructed of rolled steel. The construction makes for a long lasting product with a gloss black powder coat finish. Use 2″ – 12″ Adjustable Hose Clamps, CLP004, to secure hoses to reducer. This reducer connects ONE 6″ diameter hose to ONE 4″ diameter hose.
-
CMP023 – Desiccant Refill Material, 1 Gallon Container.
$67.00Desiccant Refill Material, (4) 1 Gallon Containers. This desiccant changes color as it absorbs water, making it easy to know when a change is necessary. Blue = Dry, Pink = Wet. Reuse this desiccant after baking the moisture out in an oven. Use this refill material with the 5-Stage Desiccant Dryer, CMP022.
-
PPE005 – MICROPOUROUS COVERALL – LARGE, 5-PACK
$62.00MICROPOUROUS COVERALL – LARGE. BARRIER AGAINST DRY AND LIQUID CHEMICAL SPLASH. HOOD, ELASTIC WRIST, ZIPPER CLOSURE ON FRONT, 5-PACK
-
PPE004 – MICROPOUROUS COVERALL – MEDIUM, 5-PACK
$62.00MICROPOUROUS COVERALL – MEDIUM. BARRIER AGAINST DRY AND LIQUID CHEMICAL SPLASH. HOOD, ELASTIC WRIST, ZIPPER CLOSURE ON FRONT, 5-PACK
-
PAT224-18 – Cammed-PSA Access Door,18″x18″
$60.00Cammed Access Door for Sheet Metal Duct Work. 18″ x 18″ Hinged Door is Secured with 4 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
-
PAT223-18 – Hinged-PSA Access Door,18″x18″
$60.00Hinged Access Door for Sheet Metal Duct Work. 18″ x 18″ Hinged Door is Secured with 2 Cam-Locks. Pressure Sensitive Adhesive flange for easy installation.
